Timer Switch with Daily Multiple Period Settings (No Neutral Required)
Model #：BRT-407
Specification.pdf

Features：

BRT-407 is the most advanced timer switch. It is controlled by a micro controller unit and has very accurate timing capability. It is designed for easy installation and retrofit, directly fit into standard wall box with no need for the neutral.
 

• One button for easy operation;
   
• Hidden panel of 9 keypads for setting up timer to prevent inadvertent changes;
   
• Up to 20 preset timing periods with precise On and Off time each day;
   
• Load up to 2000W;
   
• LCD display showing the current clock time, timing period #, and the current status of the switch;
   
• Good for all kinds of loads (Resistive, inductive, and capacitive);
   
• ABS-V0 flame resistance material; and
   
• Classical 86 series design and high quality build.
   

Front View, Back View, and Hidden Panel

Fig. 1 and Fig. 2 show the front view and the back view of the wall mount unit of BRT-407 timer switch respectively.

As shown in Fig. 1, BRT-407 timer switch has an LCD display and an On/Off buttons on the front. The LCD display shows the current time and the current status of the switch. The On/Off button is used for turning on or turning off a load. BRT-407 timer switch also has wiring terminal blocks on its back.

When the On/Off button is pressed,
The display shows On and the load will be turned on immediately; andWhen the On/Off button is pressed again,
If there is no timing period being set, the load will be turned off immediately and the display will show Off, and;
If there is timing period being set, the load will be turned on automatically during the preset timing period.

As shown in Fig. 3, the front plate can be flipped down from the top edge. A 9 keypad panel hidden behind the front plate is used for setting up the timer. Please refer to “BRT-407 Timer Switch Setup” for details.

Specification Parameters:

Input Voltage	220～240V(50Hz/60Hz)	Operation Environment	No-condensation 20-90% RH，-20℃～55℃
Wattage	2000W	Load type	All Types*
Mounting Hole Spacing	60mm	Matching Box	75mm x 75mm x 50mm
Wall Mount Unit Dimensio	86mm x 86mm x 43mm	Wall mount Unit Weight	116g

* An additional adaptor is required for capacitive loads.

Wiring Diagram and Installation Guide:

BRT-407 timer switch only requires hot wire for installation:

Hot wire (ACL): Coming from the power line with 220V;

Load wire: Going to the load.

Warning: Please make sure power is turned off before starting installation!

Fig. 4 shows the wiring diagram and Fig. 5 shows the step-by-step installation instructions.

There are three easy steps:

Step one: Use a screwdriver to pry off the front plate in position A;

Step two: Wiring according to the diagram and the labelled ports of the switch; and

Step three: Install screws and front plate.

BRT-407 Timer Switch Setup:

1.Following the wiring diagram and Installation Guide to set up the wall mount unit, and power it with 220 voltages.

2.Flip down the front plate from the top edge.

3.Set up Time and Date: Press the SET button, the displayed hours will flash, and then press – or + to adjust the hours. Press the SET button again, the displayed minutes will flash, and then press – or + to adjust the minutes. Press the SET button again, the displayed date will flash, and then press – or + to adjust the date. Finally, press the SET button to finish and the settings are saved.

4.Set up Delay off Time: The delay-off time of the two loads can be set separately. Setting up the first load: The longest delay off time is 30 minutes. Press the  Ⅰ button to set the minutes, and then press button ? or ? to adjust the minutes. Press the Ⅰbutton again to set the seconds, and then press button ? or ? to adjust the seconds. Finally, press and hold the Ⅰbutton to save the settings or the settings will be saved automatically if there is no keypad operation for 15 seconds.

Setting up the second load: Use theⅡbutton to set up the second load in the same way as setting up the first load. Setting up the third load:

Use theⅢ button to set up the third load in the same way as setting up the first load.

once the settings are finished, flip up and close the front plate. The delay off time can be deleted following Step 2 above and Step 5 below.

5.delet the Delay off Time setting: Press the Ⅰ (ⅡorⅢ) button to set the minutes to 00 using – or + , and press the Ⅰ (ⅡorⅢ) button again to set the seconds to 00 using – or +. The switch will just have a basic ON/OFF function.

At this point, the wall mount unit is ready to control the loads. In order to control the loads remotely using a remote set, the remote set needs to be synchronized with the wall mount unit.

6.Install one 12V 23A battery into the remote set.

7.Synchronize the wall mount unit with the remote: Flip down the front plate from the top edge. Press and hold Ⅰbutton for 2 seconds until the display shows . Then, press one of the 6 buttons on the remote until disappears. This button is now set up to control the first load specifically. The synchronization process can last up to 20 seconds. Another remote button can be synchronized to control the second load by usingⅡandⅢbutton, respectively.

Applications:

BRT-604 timer switch kit can be used for automatically turning off all kinds of loads such as fans, lights, appliances, or other kinds of electrical equipment. They are perfect for saving energy and bringing convenience and safety to our daily life and work. The remote set is especially handy.

The elegant design of BRT-604 timer switch makes it suitable for wide applications at various locations such as homes, schools, laboratories, hospitals, offices, etc., especially for luxurious hotels and high-grade villas.

How to Order: